Click Feedback to help us serve you better. Thanks!

2 ft Black Rubber Speed Hump Section

Item Code: SPEEDHUMPSECTION

Quantity in Cart:

None

Price: $94.95

Volume Pricing
1-9	10-39	40+
$94.95	$75.95	$65.95

Quantity:

This item ships via truck.
Before purchasing you can Click Here to submit a shipping cost quote request for this item
OR Call us at 360-989-0960 for a shipping cost quote

Black Rubber Speed Humps with molded in yellow stripes and dual bottom channels.

6 predrilled holes for hardware per section

Tough, recycled tire rubber is resistant to weather, salt, moisture, UV, oil, and temperature

Will not warp, chip, or crack

Easy, one person installation (instructions included)

Installation hardware and end caps are available but sold separately

Lightweight, Dependable, Affordable

Easy, one person installation (instructions included)

Removable for surface maintenance, snow plows or to relocate at a new site

Virgin rubber overlay with molded-in yellow road marking tape stripes

Manufacturer suggests using adhesive and hardware together if 4+ trucks a day (keeps hardware from working loose)

Dual bottom channels for drainage, wire or pipe to .75"

Male/Female joints on each section

Use multiple sections to cover width needed

6 predrilled holes for hardware per section

Withstands heavy traffic

Weight 50 lbs.

Dimensions: 3 ft W x 2 ft L x 2.25" H

Manufactured in the U.S.A. to keep Americans working.

Rubber Speed Hump Installation Instructions
For 4-10 trips per day with heavy trucks (i.e. garbage trucks) or an incline (i.e. parking garage), install using both adhesive and hardware. Not designed for more than 10 trucks per day or for speeds over 15 mph. Sweepers must raise brushes before driving over speed humps. Remove speed humps when snowplows are in use.

Mounting Rubber Speed Humps on Asphalt:
1. Drill 1/2" diameter pilot holes through asphalt or to depth of 3".
2. Clean installation area.
3. Put rubber speed hump in place. Put washers in place.
4. Put bead of adhesive on leading edges of speed humps and speed hump end caps.
5. Start asphalt rebar spikes before completely setting any individual rebar spike.

Mounting Rubber Speed Humps on Concrete:
1. Drill 3/4" holes, 2" deep and insert lag shield (threaded end goes in first). For maximum expansion, the shield should protrude slightly above concrete surface before setting.
2. Clean installation area.
3. Put product in place. Put washers in place.
4. Put bead of adhesive on leading edges of speed humps and speed hump end caps.
5. Insert lag screw starting all lags before tightening any. Tighten with wrench until firm resistance is felt.

Mounting Rubber Speed Humps with Adhesive:
1. Use 10 ounces of construction grade adhesive such as PL Premium Polyurethane or a 2-tube epoxy such as Simpson ET-22. These products can be bought from your local hardware store.
2. Put rubber speed hump in place. Mark perimeter and drill holes.
3. Brush holes and blow out debris. Clean and dry installation area to adhesive directions.
4. Mix enough epoxy for one installation (if using a 2-tube epoxy) or use a 10 oz. tube of PL Premium.
5. Fill the holes to 2" from top with adhesive.
6. Apply adhesive to bottom of speed hump. Set in place.
7. Install washers and hardware (see instructions above).
8. Allow setting and curing time according to adhesive directions. Please note if you remove speed hump installed with adhesive, you are likely to tear the speed hump or the surface.

Related Item(s)

14" x 1/2" Rebar Spike for Speed Bump/Hump or Car Stop

$2.25

4.5" Lag Screw, Washer and Shield for Speed Bump or Hump

$2.25

Black Rubber Speed Hump End Cap

$72.95

12" x 18" Slow Speed Hump Ahead Reflective Aluminum Sign

$25.95

If you need immediate assistance, please call 360-989-0960.