Click Feedback to help us serve you better. Thanks!

Pallet of 40, 6' Rubber Speed Bumps, Yellow Stripes Reflective Cateyes

Item Code: 6FTRSBSEPALLET

Quantity in Cart:

None

Price: $3,598.00

Quantity:

This item ships via truck.
Before purchasing you can Click Here to submit a shipping cost quote request for this item
OR Call us at 360-989-0960 for a shipping cost quote

Buy a pallet of 6 foot Recycled Rubber Speed Bumps with yellow molded stripes, reflective cateyes and dual bottom channels and save money with our pallet quantity discount.

Slow down drivers in your parking lot with our rubber speed bump with yellow stripes, reflective cateyes and dual cable protectors. Molded-in stripes of visible yellow road marking tape warn drivers of speed bump ahead. Eight reflective built-in cateye reflectors for night visibility. Recycled rubber for endurance that will not warp, chip or crack. Tough, recycled tire rubber is resistant to weather, salt, moisture, UV, oil and temperature. Virgin rubber overlay. Dual bottom channels for cables, drainage, wire or pipe to 3/4 inch. Rubber speed bumps conform to surface contour and can be cut with utility knife if necessary.

Designed for up to 15 mph

8 cateye reflectors for night time visability

4 mounting holes

Conform to road surface contour

Removable for surface maintenance

Easy, one person installation (instructions included)

Installation hardware is available but sold separately, see below.

Weight: 60 lbs each

Dimensions: 2.625" H x 12" W x 6 feet L

Manufactured in the U.S.A. to keep Americans working.

Picture shows dual channels under speed bump.

Rubber Speed Bump Installation Instructions:
Leave 1"-3" between speed bumps for drainage and expansion (can be cut with a utility knife if necessary). For 4-10 trips per day with heavy trucks (i.e. garbage trucks) or an incline (i.e. parking garage), install using both adhesive and hardware. Not designed for more than 10 trucks per day or for speeds over 15 mph. Sweepers must raise brushes before driving over speed bumps. Remove speed bumps when snowplows are in use.

Mounting Rubber Speed Bumps on Asphalt or Gravel:
1. Drill 1/2" diameter pilot holes through asphalt or to depth of 3".
2. Clean installation area.
3. Put rubber speed bump in place. Put washers in place.
4. Start asphalt rebar spikes before completely setting any individual rebar spike.

Mounting Rubber Speed Bumps on Concrete:
1. Drill 3/4" holes, 2" deep and insert lag shield (threaded end goes in first). For maximum expansion, the shield should protrude slightly above concrete surface before setting.
2. Clean installation area.
3. Put rubber speed bump in place. Put washers in place.
4. Insert lag screw starting all lags before tightening any. Tighten with wrench until firm resistance is felt.

Mounting Rubber Speed Bumps with Adhesive:
1. Use 10 ounces of construction grade adhesive such as PL Premium Polyurethane or a 2-tube epoxy such as Simpson ET-22. These products can be bought from your local hardware store.
2. Put rubber speed bump in place. Mark perimeter and drill holes.
3. Brush holes and blow out debris. Clean and dry installation area to adhesive directions.
4. Mix enough epoxy for one installation (if using a 2-tube epoxy) or use a 10 oz. tube of PL Premium.
5. Fill the holes to 2" from top with adhesive.
6. Apply adhesive to bottom of speed bump. Set in place.
7. Install washers and hardware (see instructions above).
8. Allow setting and curing time according to adhesive directions. Please note if you remove speed bump installed with adhesive, you are likely to tear the speed bump or the surface.

Related Item(s)

14" x 1/2" Rebar Spike for Speed Bump/Hump or Car Stop

$2.25

4.5" Lag Screw, Washer and Shield for Speed Bump or Hump

$2.25

Black Recycled Rubber Speed Bump End Cap

$19.95

If you need immediate assistance, please call 360-989-0960.