![](javascript:EmailToFriend("http://www.rvparksupplies.com/mm5/ShowForward.php?product=3FTRCSQTY60&price=$15.95&image=graphics/00000001/3FTRCS.jpg"))
|
3 ft Rubber Car Parking Stops, Wheel Stops, Price each for 60 or morePrice: $15.95 This item ships via truck. 
|
Price each for 60 or more 3 ft Rubber Car Stop or Parking Stop with 2 stripes on each side and 2 hardware mounting holes. Tough, recycled tire rubber is resistant to weather, salt, moisture, UV, oil and temperature. Will not warp, chip or crack. Reflective stripes are made of road marking tape. Bonded stripes are available in yellow, white, blue or none. Easy, one person installation (instructions included).
Installation hardware is available but sold separately. Please see part number ASPHALTSPIKE for asphalt installation hardware. Please see part number CONCRETESCREWCARSTOP for concrete mounting hardware.
Weight 20 lbs.
Dimensions: 6" W x 4.25" H x 3 feet L.
PLEASE SPECIFY STRIPE COLOR ABOVE.
Manufactured in the U.S.A. to keep Americans working.
Rubber Wheel Stop Installation Instructions:
Mounting Rubber Wheel Stops on Asphalt:
1. Drill 1/2 inch diameter pilot holes through asphalt or to depth of 3 inches.
2. Clean installation area.
3. Put rubber wheel stop in place. Put washers in place.
4. Start asphalt rebar spikes before completely setting any individual rebar spike.
Mounting Rubber Wheel Stops on Concrete:
1. Drill 3/4 inch holes, 2 inches deep and insert lag shield (threaded end goes in first). For maximum expansion, the shield should protrude slightly above concrete surface before setting.
2. Clean installation area.
3. Put product in place. Put washers in place.
4. Insert lag screw starting all lags before tightening any. Tighten with wrench until firm resistance is felt.
Mounting Rubber Wheel Stops with Adhesive:
1. Use 10 ounces of construction grade adhesive such as PL Premium Polyurethane or a 2-tube epoxy such as Simpson ET-22. These products can be bought from your local hardware store.
2. Put rubber wheel stop in place. Mark perimeter and drill holes.
3. Brush holes and blow out debris. Clean and dry installation area to adhesive directions.
4. Mix enough epoxy for one installation (if using a 2-tube epoxy) or use a 10 oz. tube of PL Premium.
5. Fill the holes to 2 inches from top with adhesive.
6. Apply adhesive to bottom of wheel stop. Set in place.
7. Install washers and hardware (see instructions above).
8. Allow setting and curing time according to adhesive directions. Please note if you remove wheel stop installed with adhesive, you are likely to tear the wheel stop or the surface.
Go to top of this 3 ft Rubber Car Parking Stops, Wheel Stops, Price each for 60 or more page.
Installation hardware is available but sold separately. Please see part number ASPHALTSPIKE for asphalt installation hardware. Please see part number CONCRETESCREWCARSTOP for concrete mounting hardware.
Weight 20 lbs.
Dimensions: 6" W x 4.25" H x 3 feet L.
PLEASE SPECIFY STRIPE COLOR ABOVE.
1. Drill 1/2 inch diameter pilot holes through asphalt or to depth of 3 inches.
2. Clean installation area.
3. Put rubber wheel stop in place. Put washers in place.
4. Start asphalt rebar spikes before completely setting any individual rebar spike.
Mounting Rubber Wheel Stops on Concrete:
1. Drill 3/4 inch holes, 2 inches deep and insert lag shield (threaded end goes in first). For maximum expansion, the shield should protrude slightly above concrete surface before setting.
2. Clean installation area.
3. Put product in place. Put washers in place.
4. Insert lag screw starting all lags before tightening any. Tighten with wrench until firm resistance is felt.
Mounting Rubber Wheel Stops with Adhesive:
1. Use 10 ounces of construction grade adhesive such as PL Premium Polyurethane or a 2-tube epoxy such as Simpson ET-22. These products can be bought from your local hardware store.
2. Put rubber wheel stop in place. Mark perimeter and drill holes.
3. Brush holes and blow out debris. Clean and dry installation area to adhesive directions.
4. Mix enough epoxy for one installation (if using a 2-tube epoxy) or use a 10 oz. tube of PL Premium.
5. Fill the holes to 2 inches from top with adhesive.
6. Apply adhesive to bottom of wheel stop. Set in place.
7. Install washers and hardware (see instructions above).
8. Allow setting and curing time according to adhesive directions. Please note if you remove wheel stop installed with adhesive, you are likely to tear the wheel stop or the surface.
